Dry Cure chamber project
Drum Smoking Big Poppa Smokers
Loyalty Program
Need Pellets?
Dry Cure chamber project
Page 1 of 2 12 LastLast
Results 1 to 10 of 11

Thread: Dry Cure chamber project

  1. #1

    Dry Cure chamber project

    Well I began today. Long ways to go still. Going to try to add some pics to the thread from my droid phone. Wish me luck.

    TD

  2. #2

  3. #3

  4. #4
    Watching...
    <><
    MAK 1 Star General #651 - 2014 Model
    former owner - MAK 1 Star General #171
    22.5" Weber Performer with Stoven Pellet Grill attachment
    27 + year old 22.5" Weber Kettle (still works fine)
    Modified Horizontal Offset Smoker - used mainly for cold smoking.

  5. #5
    Senior Member Tatonka3A2's Avatar
    Join Date
    Jan 2012
    Location
    Glenburn, ND
    Posts
    1,009
    Very cool!!

  6. #6
    Well I'm stalled out on this for the moment. I'd originally planned to use an STC-1000 temp controller to run the fridge and installed lights for heating/cooling. For humidity control, I had planned to operate a an ultrasonic humidifier via a humidity controller. there was no means to do both humidification and dehumidification without a second humidity controller, and the two would need to be manually turned on or off. There is no means of temp/RH% logging. Then I stumbled onto someone else's project that offered all of these options with control via an Arduino Uno. So I am stalled at the programming phase. The wiring, I have a decent concept about. The programming, I know basically nothing about: dabbled with stuff in my teens and college, but that was it. This is way over my head, and unless I can get some specific help or advice, its going to be a long time for me learn how to write the code to operate the controller(s) to do what I want.

    I'll hopefully be figuring this out in the next few months, and will proceed with either that dumb temp controller/humidity controller option, or get a programmer to help me out.

    TD

  7. #7
    Well had a breakthrough on this today. I was able to get the code to compile and upload to my Uno board. Next steps are going to be wiring it all up and final hardware mounting, etc.

    More to come, and hopefully soon!

    TD

  8. #8
    Dick, glad you got it figured out. You have me intrigued with this Arduino Uno controller, and I see they are relatively inexpensive to boot.
    <><
    MAK 1 Star General #651 - 2014 Model
    former owner - MAK 1 Star General #171
    22.5" Weber Performer with Stoven Pellet Grill attachment
    27 + year old 22.5" Weber Kettle (still works fine)
    Modified Horizontal Offset Smoker - used mainly for cold smoking.

  9. #9
    Yes. In addition you need some additional electronics: fan (s), some lamps if you want to heat/ferment or live somewhere cold, some relays, an LCD display, and a few other components. The Ultrasonic humidifier is perhaps the most expensive piece, besides the fridge.

    I should be wiring my unit up soon.

    The coding on the Arduino Uno I think needs additional work to enable some of the primary functions, and to streamline its operation, but from what I have seen, it does work at controlling humidity up or down and temperature down. Can optionally be modified to make a cold smoker or even hot smoker.

    I am waiting for a couple of parts from UPS and then I'll be testing out my wiring abilities!

    TD

  10. #10
    OK. SO I think I fouled up the sensor. New one arrives tomorrow. I believe that I have all the wiring correct on the test setup. Once I can confirm that its working, I'll do the final wiring. With luck might finish over the weekend. Also, at the local sausage shop where they do dry cure and fresh sausages, I obtained the source for their casings. You can buy pre-flushed and tubed! Unfortunately the arrival of 90+ days in FL will probably prevent me from doing much until fall, but maybe I'll do a few small batches indoors. My indoor kitchen is pretty small for all the grinding and stuffing apparatus.
    The Uno board I have is the Italian Arduino one, and was $27 I think. Its all open source though, and you can get China made versions for under $10. I ordered two of these for some additional projects: Temp controlled proofing chamber, TBD.
    TD

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •